The 1000/1v2 mono amplifier puts out 1,000 watts RMS of clean power to your subwoofer system, and JL Audio’s patented Class-D amp circuitry keeps a tight rein on cone movement. The cast aluminum heatsinks dissipate heat quickly, giving these amps long lifespans and reliable operation. You can stack multiple Slash v2 amps, saving you valuable space in your trunk or cargo area.

JL Audio amps use “differential-balanced inputs” to isolate the signal’s ground from the chassis ground, reducing noise and making Slash v2 amplifiers compatible with almost any system, including most factory radios. Tunable frequency filters and a parametric EQ bass boost give you precise control over your bass sound, and the optional RBC-1 remote lets you dial in the right amount of thump from the front seat.

Details:

• mono subwoofer amplifier
• 1,000 watts RMS x 1 at 1.5 to 4 ohms
• Regulated, Intelligent Power Supply system
• differential-balanced inputs
• variable low-pass filter (40-200 Hz, 12 or 24 dB/octave)
• parametric EQ bass boost (0-15 dB at 20-80 Hz)
• variable infrasonic filter (-24 dB/octave at 15-60 Hz)
• optional wired remote bass boost
• Class-D amplifier design
• MOSFET power and output stages
• speaker- and preamp-level inputs
• preamp outputs
• 4-gauge power and ground leads and a 100-amp fuse recommended — wiring and hardware not included with amplifier
• no on-board fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended
• 19-3/4″W x 2-5/16″H x 10-1/16″D
• warranty: 2 years

JL Audio has been specializing in car audio products since 1975 (national distribution of JL’s subwoofers began in 1992), and it goes without saying that JL Audio has long been considered a major player in the subwoofer marathon that we have been witnessing for the past years. Known for their innovative engineering approach to speaker design, JL Audio has produced some very real improvements in subwoofer technology. They were among the earliest companies to use layered voice coil windings beyond four layers, and their patented vented reinforcement collar (VRC) that greatly strengthens the critical bond between the voice coil former, spider and cone was also a smart idea for its time.

Performance Overview:

• Superb sound quality
•  Extremely long linear excursion capability yields reduced distortion and outstanding output capability.
• Moderate box volume requirements
• High Power Handling

Specifications:

• Nominal Diameter: 15 inches (380 mm)
• Continuous Power Handling: 500 Watts
• Voice Coil: 2.5″ diameter, 4-layer, Kapton former
• Available Configurations: Dual 2 ohm or Dual 4 ohm
• Xmax (one-way, linear): 0.68″ (17.1 mm)
• Sealed Enclosure Range: 1.50-2.75 cu.ft. (42.5-78.0 liters)
• Ported Enclosure Range: 2.50-4.00 cu.ft. (71.0-113.0 liters)
• VRC” Technology: YES
• Cross-Drilled Pole Piece: YES
• Elevated Frame Technology: YES

 

• Switchable inputs work with RCA’s or speaker wire inputs
• Crossover can be set from 40 Hz to 200 Hz for system tuning
• Preamp output lets you link the amp to another amp
• Accepts 8 gauge speaker wire and 4 gauge power and ground wire

Basics
Product Type:	Amplifier
Amplifier Type:	1-channel
Dimensions (W x D x H):	9.3 in x 10.2 in x 2.4 in
Manufacturer Warranty:	Limited warranty – 2 years
Audio Performance
Signal-To-Noise Ratio:	95 dB
Amplifier Output Details:	250 Watt – 1.5/4 Ohm – 1 channel(s)
Total Harmonic Distortion:	0.0005
Input Signal Voltage:	0.2 – 2V, 0.8 – 8V
Inputs And Outputs
Connector Types:	1 x audio input ( RCA phono x 2 ) 1 x audio line-out ( RCA phono x 2 ) 2 x speakers output