Street Sounds Online » Kicker

Kicker CVR 0712

scott136 — Thu, 15 Feb 2007 16:58:49 +0000

Kicker builds the CompVR round subwoofers to endure the the harsh demands of producing big bass. Each sub houses an injected-molded polypropylene cone and Santoprene™ rubber surround in a high-strength steel basket with plenty of interior venting. Kicker’s SoloKon™ cone design looks fantastic while it protects against flexing that can wreck your sub and your sound.The 07CVR122 12″ sub boasts dual 2-ohm voice coils that can manage a heavy power onslaught, while adding more options for wiring up your system.UniPlate construction molds parts of the sub’s motor structure together as a single unit to optimize heat transfer, improve accuracy, and extend cone excursion.Kicker CompVR subs can be used for marine applications, so make some waves with these stellar subwoofers.

Details:
	»	12″ subwoofer with dual 2-ohm voice coils
	»	injection-molded polypropylene cone
	»	ribbed Santoprene rubber surround
	»	suitable for marine use
	»	power handling: 50-400 watts RMS (200 watts per coil)
	»	800 watts peak power handling
	»	frequency response: 25-500 Hz
	»	sensitivity: 86.7 dB
	»	top-mount depth: 6-1/4″
	»	sealed box volume: 1.0-4.6 cu. ft.
	»	ported box volume: 1.75-2.25 cu. ft.

Kicker KQ9 Signal Processor

scott136 — Mon, 06 Nov 2006 14:46:39 +0000

You bought some great audio equipment for your car, but you’re only halfway there. Now you have to tune your system in order to get the performance you crave. Kicker packs a ton of useful sound-shaping features into the compact KQ9 preamplifier: 9 bands of equalization, high- and low-pass crossovers, fader control, speaker- and preamp level inputs, and subwoofer level control — all in a 1/2 DIN-sized box that installs in (or under) your dash!The KQ9 features one set of RCA inputs; speaker-level inputs are also available if your receiver doesn’t have preamp outputs. Three sets of outputs are available for connection to your outboard amplifiers. You can adjust 8 bands of equalization for your main speakers: cut or boost up to 12 dB at 125, 250, 500, 1,000, 2,000, 4,000, 8,000, and 16,000 Hz. The subwoofer output features a separate sub-bass EQ (cut/boost up to 12 dB, variable from 40-60Hz) and a level control (0 to +6 dB).

If you’re using a subwoofer, the high-pass crossover (100 Hz at 18 dB per octave) removes low frequencies from your full-range speakers for greater efficiency, while the low-pass crossover (variable 60-120 Hz, at 18 dB per octave) controls the quality of the bass being sent to your sub. The EQ Defeat switch allows you to compare equalized and non-equalized sound instantly.

Details:

1/2 DIN size — installs in or under your dash (underdash brackets included)
8 bands of equalization (12 dB cut/boost at 125, 250, 500, 1,000, 2,000, 4,000, 8,000, and 16,000 Hz)
variable subwoofer EQ (variable from 40-60 Hz, 12 dB cut/boost)
subwoofer level control (0 to +6 dB)
high-pass crossover (100 Hz at 18 dB per octave)
low-pass crossover (variable 60-120 Hz, at 18 dB per octave)
preamp- and speaker-level inputs
three sets of RCA outputs (this unit has no built-in amplification — amplifiers are required)
switchable green/amber illumination
EQ defeat switch
input sensitivity: 150 mV to 10 volts
7-1/8″W x 1″H x 5-1/16″D

Kicker CVR154 Subwoofer

scott136 — Mon, 06 Nov 2006 14:38:21 +0000

Great power handling and wiring flexibility distinguish Kicker’s CompVR subs. The CVR154 15″ dual voice coil sub can handle a ton of power. The CVR154 features a rigid polymineral cone that’ll stand up to the demands of high-level playback. Kicker designed the sub for extended cone travel, and perimeter venting in the non-resonant steel basket helps to keep the sub running cool. Dual 4-ohm voice coils add versatility when you wire up your system.

Details:
	»	15″ sub with dual 4-ohm voice coils
	»	suitable for marine use
	»	injection-molded polymineral cone with double-stitched, foam-ribbed Santoprene rubber surround
	»	non-resonant steel basket
	»	frequency response: 25-500 Hz
	»	power handling: 50-500 watts RMS (250 watts per voice coil)
	»	peak power: 1000 watts
	»	sensitivity: 89.1 dB
	»	top-mount depth: 8-1/16″
	»	sealed box volume: 1.8-5.2 cu. ft.
	»	ported box volume: 3.00-5.00 cu. ft.

Kicker 05Dcvr122 Vented Subwoofer Enclosure

scott136 — Mon, 06 Nov 2006 14:29:13 +0000

The two CompVR subs in Kicker’s 05DCVR122 enclosure move lots of air, thanks to rigid cones and durable Santoprene surrounds. Air vents around the perimeter of the heavy-duty steel baskets keep the subs running cool.

Kicker builds the box with rock-solid 3/4″ medium density fiberboard, so it’ll stay tight no matter what the subs dish out. The gray and black carpet covering lends the box a stylish look that will complement any interior. A single set of speaker terminals simplifies hookup and ensures maximum power output from most mono subwoofer amps.

Details:
	»	ported hatchback-style enclosure with two 12″ CompVR subwoofers
	»	3/4″ medium density fiberboard construction covered with grey and black carpet
	»	2-ohm total impedance
	»	power handling: 50-600 watts RMS (1200 watts peak power)
	»	frequency response: 25-500 Hz
	»	sensitivity: 98 dB
	»	32-3/8″W x 16″H x 17-3/8″D1 x 13-15/16″D2

Kicker 05DC122 Vented Subwoofer Enclosure

scott136 — Thu, 02 Nov 2006 14:37:05 +0000

The two Comp subs in Kicker’s 05DC122 enclosure move lots of air, thanks to rigid cones and durable double-stitched foam surrounds. Air vents around the perimeter of the heavy-duty steel baskets keep the subs running cool.

	»	ported hatchback-style enclosure with two 12″ Comp subwoofers
	»	3/4″ medium density fiberboard construction covered with gray and black carpet
	»	2-ohm total impedance
	»	power handling: 300 watts RMS (600 watts peak power)
	»	frequency response: 20-200 Hz
	»	sensitivity: 99.9 dB
	»	32-1/4″W x 16-1/6″H x 17-1/4″D1 x 14″D2

Kicker ZX350.2 Amplifier

scott136 — Thu, 02 Nov 2006 14:26:52 +0000

If you’re into great sound, you’ll love Kicker’s ZX series amplifiers. These high-end amps set the standard for powerful sound, with a distinctive look that’ll make your installation stand apart from the crowd.The ZX350.2 2-channel amp will drive your speakers with over 100 watts of power per channel. No inflated “peak power” ratings here — you can trust that this amp’s CEA-2006 compliant rating reflects a true measure of its capabilities. Efficient heat sinks and rugged internal components ensure reliable operation and clean power output when the volume is cranked.

The built-in variable frequency filters adjust the amp’s output to get the most out of your speaker setup, whether you’re running full-range speakers or subs. Use the bass boost control to dial in the exact amount of low-end bump you’re looking for, then use the included wired remote control to kick up the bass right from the driver’s seat.

	»	2-channel car amplifier
	»	110 watts RMS x 2 at 4 ohms (175 watts RMS x 2 at 2 ohms)
	»	350 watts RMS x 1 in bridged mode (4-ohm stable in bridged mode)
	»	variable high- and low-pass filters (50-200 Hz, 12 dB per octave)
	»	variable bass boost (0-18 dB at 40 Hz)
	»	wired remote bass level control
	»	top-mounted controls
	»	CEA-2006 compliant
	»	speaker-level inputs
	»	preamp inputs and outputs
	»	fuse rating: 25A x 2
	»	8-gauge power and ground leads recommended — wiring and hardware not included with amplifier
	»	13-1/2″W x 2-5/16″H x 9-5/8″D
	»	warranty: 2 years

Kicker ZX400.1 Amplifier

scott136 — Sat, 28 Oct 2006 13:33:53 +0000

These high-end amps set the standard for powerful sound, with a distinctive look that’ll make your installation stand apart from the crowd.The ZX400.1 mono subwoofer amp will drive your subs with up to 400 watts of power. No inflated “peak power” ratings here — you can trust that this amp’s CEA-2006 compliant rating reflects a true measure of its capabilities. The efficient Class D design draws less current and produces less heat than traditional amps, for reliable operation that won’t strain your car’s electrical system.

The built-in variable low-pass filter adjusts the amp’s output to get the most out of your subwoofer, while a subsonic filter removes the extreme low bass that hampers system efficiency. Use the bass boost control to dial in the exact amount of low-end bump you’re looking for, then use the included wired bass level remote control to pump up the volume right from the driver’s seat. And for the best deal on the net go HERE!

	»	mono subwoofer amplifier
	»	200 watts RMS x 1 at 4 ohms (400 watts x 1 at 2 ohms)
	»	variable low-pass filter (50-200 Hz at 24 dB per octave)
	»	variable bass boost (0-18 dB at 40 Hz)
	»	subsonic filter (12 dB at 25 Hz)
	»	wired remote bass level control
	»	Class D design
	»	CEA-2006 compliant
	»	speaker-level inputs
	»	preamp inputs and outputs
	»	fuse rating: 40A x 1
	»	4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
	»	10-1/4″W x 2-5/16″H x 9-5/8″D

For the best deal on the net go HERE!

Kicker S12L5 Subwoofer

scott136 — Tue, 24 Oct 2006 13:29:32 +0000

From top to bottom, Kicker builds the Solo-Baric L5 subs for powerhouse bass. The 06S12L54 12″ subwoofer features Kicker’s trademark square woofer cone, crafted from composites and treated with aluminum — it’s rigid, responsive, and ready for hard-hitting, accurate playback at extreme sound pressure levels. The tough, tear-resistant Santoprene surround includes reinforcement at the edge of the cone for added durability.A sturdy steel basket holds these elements in place, while air vents around the sub’s perimeter pump the hot air away from the interior. Kicker’s UniPlate pole piece and backplate allow extended cone travel, so the sub won’t distort when the lows start bumping. The two 4-ohm voice coils offer the wiring flexibility you’ll need to use your sub in either high output or multiple woofer configurations. And for the best deal on the net go HERE!

	»	12″ subwoofer with dual 4-ohm voice coils
	»	SoloKon aluminum-treated composite cone with Santoprene surround
	»	rigid steel basket
	»	power range: 50-600 RMS watts (300 watts per voice coil)
	»	peak power: 1200 watts
	»	frequency response: 20-100 Hz
	»	sensitivity: 88.9 dB
	»	mounting depth: 6-7/8″
	»	sealed box volume: 0.88-2.00 cubic feet
	»	ported box volume: 1.75-3.25 cu. ft.

For the best deal on the net go HERE!

Kicker ZX1000.1 Amplifier

scott136 — Fri, 20 Oct 2006 13:34:13 +0000

KICKER amplifiers combine remarkably advanced design with the highest-grade electronic components for the ultimate combination of sound quality and brute power. Beneath the exciting new ZX series exterior lies internals that have been designed from the ground up to deliver tight, clean power. Efficient Class D circuitry allows the amplifier to really pour on the power in 2-ohm operation.

All this power is at your command with a variable crossover, high- and low-level inputs, and defeatable subsonic filter to help protect your subs. Fast-acting protection circuitry guards against short-circuits, over-voltage, overheating, or wiring mishaps. Gold-plated RCA input and output connectors insure maximum conductivity and resistance to corrosion. High 22kOhm input impedance lets you link multiple amplifiers in a single signal chain without having to use signal-robbing splitters.

Custom-tooled remote and speaker screw terminals are also gold-plated, while oversized power and ground terminals allow for large gauge wire connections. Dialing up just the right amount of bass is at your fingertips with the included remote KickBass variable bass boost. KICKER even ships every amp with its own birth certificate – KICKER’s guarantee to you that it meets their high standards for power and performance.And for the best deal on the net go HERE!

Class D mono subwoofer amplifier: Provides massive power to your subwoofer without drawing lots of power from your system.

Power output: 500 watts RMS at 4 ohms or 1000 watts of peak power at 2 ohms.

Protection circuitry: Protects against short circuits, overloads, heat and reverse polarity.

Expansion options: Speaker-level and RCA inputs make it easy to add on to your system.

Variable crossover: A high/low pass filter optimizes the sound by sending the selected frequencies to your subwoofers or speakers. This amp has a 24db per octave electronic crossover, greatly increasing the range at which you can fine-tune your system. It can also be by-passed for full-range operation.

MOSFET: Runs cooler and more efficiently.

Cooling fan: Offers extra protection against heat when the amplifier is running at high levels.

Remote bass control: Place the controller on your dash or console to change the amount of bass going to your subwoofer without leaving the driver’s seat

RMS Power @ 4 Ohms: 500W x 1 @ 4 ohms

THD at 4-Ohm RMS Power: <1 %

Bridged RMS Power @ 4 Ohms: 1,000W x 1 @ 2 ohms

Speaker Level Inputs: yes

Preamp Outputs : yes

Built-In Crossovers: LP

Bass Boost: 0 – 18 dB

Frequency Response: 25-200Hz

Signal to Noise Ratio: 60 dB

For the best deal on the net go HERE!

Kicker S15L5 Subwoofer

scott136 — Wed, 18 Oct 2006 15:02:57 +0000

Kicker 06 S15L5 D4 L5 inherits the same inner workings as the L7, like the cutting-edge SoloKon, the vacuum-formed, ultra-rigid cone used to push massive amounts of air. And just as its predecessor, L5s motor structure uses high-temp dual voice coils, a poly-cotton semi-progressive spider, long-lasting tinsel leads, the effective UniPlate pole piece/back plate, and a T-cut top plate for dispersing heat and creating immense power handling.

Kicker has unleashed some new 06 subwoofer models that have their competition cringing in fear. From the Comp to Kicker L7 these woofers are meant for performance, and they just happen to look pretty stylish also.And for the best deal on the net go HERE!

Peak Power Handling 1500Watts
RMS Power Range 750Watts
Impedance ( Ohms ) Dual 4-Ohm
Free-Air No
Dual Voice Coil Yes
Sensitivity 90.3dB
Frequency Response 18-100Hz
Cone Material SoloKon
Surround Material Santoprene Rubber
Dimensions
Sealed Box Volume (cu ft) 1.5-6.0 cu ft
Ported Box Volume (cu ft) 3.0-6.0 cu ft
Top Mount Depth 8-”
Cutout Diameter or Length 13-

For the best deal on the net go HERE!